Your shopping cart
Your shopping cart is empty!
MSD's Non-Magnetic Pick-Ups are engineered for extreme applications. In fact, this Pick-Up was designed and tested on 300+ mph top fuel dragsters! To live up to MSD's demanding expectations in these extreme applications, we took it upon ourselves to design and build the Pick-Ups in-house. This way we can control every aspect of their assembly and quality. Each Pick-Up is hand wound on a special ..
The HVC Distributors incorporate a magnetic pickup for the most accurate signal possible. Two pickups are stacked atop each other so if a driver switches to the secondary ignition any custom firing or timing will be unaffected. The second pick is also adjustable +/- 8 degrees.BrandMSDEmission Code5Part Number83565..
The MSD Magnetic Pick-Up replacement is the same high output assembly that is currently found in all MSD Distributors. It is supplied with the two pin connector installed.Features:Replacement maintenance-free magnetic pickupFound in all Pro-Billet DistributorsBrandMSDEmission Code5Part Number84661..
This is a replacement pickup for older style crank trigger systems that require a magnetic pickup. This pickup is magnetic and must be used with a trigger wheel equipped with steel studs to create a signal. The pickup is .75" x 16" x 2.25".BrandMSDEmission Code5Part Number8505..
The stabilizer converts the signal from a magnetic pickup to a square wave trigger signal for the MSD Ignition control.BrandMSDEmission Code5Part Number8509..
The PN 8728 can be installed on engines with a GM HEI Ignition, Ford or Chrysler electronic ignition, any standard breaker points systems or even with an MSD 5 or Blaster Ignition (non-CD ignitions). The Soft Touch Rev Control is adjusted with plug-in modules and is supplied with 6,000, 7,000 and 8,000 rpm modules. When the engine reaches your set rpm, the Soft Touch circuitry kicks in and drops t..
The Dual Channel Power Grid incorporates a high speed 32 bit microprocessor and PC software, called MSD View via a USB BluetoothTM wireless. It includes a high speed data acquisition recording engine RPM, timing, dual Tach signal, launch/WOT with sample rates of 100 samples per second or 10 milli seconds. The MSD View software will program timing curves with up to 30 points at 1.0 increments dow..
The Pro Mag A/Fuel Power Grid Controller is designed for use with the MSD Pro Mag 44 in drag racing applications, which compete in the Top Alcohol Dragster category or sanctioning bodies that allow electronic ignition timing control when using a single or dual Pro Mag system. Although the Power Grid Controller has dual outputs it can be used with, a single Pro Mag or Dual Pro Mag that allows you ..
Racing produces a tremendous amount of vibration. Tire shake and engine power, not to mention the occasional bump and grind in the corners all contribute to shortened component life. These vibration mounts are just the thing to help isolate severe racing vibrations from the 44 amp coil and other accessories. .79" x 1" - 4 included. PN8822 Fits The Following Products: • Pro Mag 44Amp Electronic ..
The pick-up wires are wound together and routed through a special aluminum skinned sleeve that connects to ground. This provides a ground shield around the trigger wires. The Harness is six feet long and is equipped with matching 2-Pin connectors. Recommended with MSD Digital Ignitions and aftermarket EFI racing systems.BrandMSDEmission Code5Part Number8862..
Trust MSD to provide quality replacement parts and wiring for your build. We provide a variety of service parts and replacement wiring harness for our popular products. Whether you're freshening your car, or have a wiring harness that has one too many splices, we have you covered. Replace them with original components that come straight from the factory.Features:Replacement Shielded Mag Cable f..
If you are using the magnetic pickup input (green and violet wires) to trigger your MSD Ignition, you will need the PN 8920 Tach Adapter. The PN 8920 will correct the operation of most voltage-triggered tachometers that do not work directly off the tach output terminal of the MSD control. This Adapter should also be used on current-triggered tachs (hooked in series with the ignition switch).Featur..
TREMEC MAGNUM XL TRANSMISSION KIT..
Let me help you spend some money :)