Your shopping cart
Your shopping cart is empty!
The Power Grid Ignition Control has been specially designed to mount to the Power Grid System Controller box, PN 7730/77303. This Ignition output only controller packs higher output than the current programmable units! For use with Power Grid Controller only, PN 7730 or PN 77303Features:For use with Power Grid PN 7730 or PN 77303 onlyHigh output spark for Power Grid SystemPower Grid PN 7730/7730..
This hub allows you to expand the Power Grid system with up to four accessory modules.BrandMSDEmission Code5Product TypePower Grid ControllerPart Number7740..
This hub allows you to expand the Power Grid system with up to four accessory modules.BrandMSDEmission Code5Product TypePower Grid ControllerPart Number77403..
Must be used with CAN-Bus Hub, PN 7740 to complete circuit. Without the CAN-Bus Terminator in place at the end of the CAN-Bus system, signals could be distorted. These distorted signals could result in permanent or intermittent problems that include but are not limited to; improper timing, false signals, and repetitious signals. Always be sure to have the MSD Controller and the CAN-Bus Terminator ..
Change the launch rpm limit (2-Step) on the fly, no need to login into software.Features:Make last minute changesChange Shift Light and RPM LaunchBrandMSDEmission Code4Part Number7751..
Now there is even more control with the PN 7761 module for the Power Grid System Controller. This module sets rpm limits based on slew rate (rpm acceleration) or based on time since launch. All of this is programmed seamlessly in MSD View. The ARC module stands for Advanced RPM Control, it basically allows your race car to remain consistent, pass after pass, controlling your engines rpm curve du..
This Power Grid module does exactly as its name sugests; retards the ignition timing in relation to boost, pressure. It also has an output wire that can be used to activate another device based on boost pressure, as well as an overboost shut-down feature that will shut the ignition off if boost exceeds the overboost target.BrandMSDEmission Code4Part Number7762..
MSD Boost Controllers are the most accurate and easy to use controllers on the market. Both controllers plug directly into the Power Grid via the CAN bus which allows user to make adjustments through MSD View software. MSD Boost controllers feature two boost curves that can be toggled on the fly, a user adjustable boost vs. timing retard curve, pressure switch and an over boost shutdown to protect..
The MSD Power Module is a fully programmable, four stage solid state relay that can handle up to 20 Amps of current per channel. The Power Module eliminates the need for electromechanical relays, fuses and timers. Outputs can be controlled independently or simultaneously, giving great flexibility. It can be configured as a digital output (i.e. ON/OFF) or as a Pulse Width Modulated output (i.e. PW..
The MSD Power Module is a fully programmable, four stage solid state relay that can handle up to 20 Amps of current per channel. The Power Module eliminates the need for electromechanical relays, fuses and timers. Outputs can be controlled independently or simultaneously, giving great flexibility. It can be configured as a digital output (i.e. ON/OFF) or as a Pulse Width Modulated output (i.e. PW..
Add valuable data logging capability to your Power Grid with the addition of the plug-n-play Wide Band O2 Module. Aside from providing O2 data to your Grid, the module also provides a 0-5v output to drive an air/fuel ratio gauge or provide a signal to other data loggers. Multiple modules and sensors can be connected to a single Power Grid setup if desired. The completely sealed unit uses a Bosc..
The Dual Channel Power Grid incorporates a high speed 32 bit microprocessor and PC software, called MSD View via a USB BluetoothTM wireless. It includes a high speed data acquisition recording engine RPM, timing, dual Tach signal, launch/WOT with sample rates of 100 samples per second or 10 milli seconds. The MSD View software will program timing curves with up to 30 points at 1.0 increments dow..
The Pro Mag A/Fuel Power Grid Controller is designed for use with the MSD Pro Mag 44 in drag racing applications, which compete in the Top Alcohol Dragster category or sanctioning bodies that allow electronic ignition timing control when using a single or dual Pro Mag system. Although the Power Grid Controller has dual outputs it can be used with, a single Pro Mag or Dual Pro Mag that allows you ..
Solid Harness.BrandMSDEmission Code5Part Number7780..
Let me help you spend some money :)