Special Offers

Adj. Sec. Pump Cam Bracket - Allows tuning of secondary idle air flow with a screwdriver and without removal of the carburetor. Nickel plated for protection and good looks, comes with retaining screw and instructions. BrandQuick FuelColorZincEmission Code5MaterialSteelProduct TypeAccelerator Pump Cam AssortmentPart Number63-2QFT..

This device will help you remove the weak OEM pencil coil in favor of a higher output Blaster SS or HVC coil.BrandMSDEmission Code3Product TypeIgnition and Electrical ComponentsPart Number6302..

Because of the additional sealing needed with vacuum systems, simply hand tightening the wing nuts may not be sufficient. The unique speed studs allow a quick, easy removal with a 1/2" socket. The lightweight, aluminum body is clear anodized for a long lasting finish. 1/4"-20x1-1/2" set screws and a 4 3/8" aluminum body are supplied. Set screws may be secured to the head or to the aluminum body. T..

Black Oxide Coated Studs & Cadmium Plated Nuts Features:(12) Pieces 3/8"-16 x 1.5" Studs & NutsBrandMr. GasketEmission Code5FinishBlack OxideMaterialSteelProduct TypeHeader BoltsWarrantyLimited 90 Day WarrantyWeight0.6500Part Number6312..

Increases horsepower and reduces underhood temperatures. Withstands 1200degrees F continuous, 2000degrees F peak. Fastens with Inferno-Ties. 1"w x 50' x 1/16" thick. Non flammable, made in USA of premium grade materials. One package will wrap one typical small block or sport compact header. BrandMr. GasketColorWhiteEmission Code5Product TypeHeat ShieldingSize1" Wide x 50' LongWeight0.7500Part Numb..

Mr. Gasket Inferno Shield Exhaust Wrap will help to reduce under hood temperatures for better performance. This wrap comes in a 2 in x 50 ft x 1/16 in thick roll. This roll is long enough to wrap one small block header or sport compact header. 1 in roll available. This nonflammable wrap will withstand temperatures up to 1200 degrees F continuously and 2000 degrees F peak. Resists petroleum apg_..

Non-flammable, resists water, fungus and petroleum apg_products. Not for use on exhaust applications. 1-1/2"W x 15'L.BrandMr. GasketEmission Code5Product TypeHeat ShieldingWeight0.5000Part Number6323..

Adjustable I.D. from 1/4" to 7/16". Not for use on exhaust applications. 25 ft. length.BrandMr. GasketEmission Code5Product TypeHeat ShieldingWeight4.8000Part Number6326K..

This is a high quality carburetor stud that looks good and works well in all applications. This stud has a bullet tip which allows for easy carburetor installation and eliminates that problem of carb getting hung on the treads and not going down straight to the intake.Features:This Stud Has A Black Oxide CoatingFine Threads On One End Fits Most IntakesBullet Nose Makes Carb Installation EasyHas Z..

These are high quality bolts that are easy to use. They have a bullet nose which is rounded for ease of installation, and that helps those carburetors slid down on the studs easier.Features:Features Bullet Nose For Ease Of InstallationMade Of SteelHas A Black Oxide CoatingCoating Resists CorrosionExtra Long 2.00 InchBrandMr. GasketColorBlackEmission Code5FinishBlack OxideLength2.00 InchMaterial..

Mr. Gasket Pipe Plugs 8 Piece Kit can be used to plug vacuum accessory holes for intake manifolds or fill plug holes in transmissions and rear ends.Features:8 Piece KitSocket HeadChrome Plated SteelAdapter TypeNPT PlugBrandMr. GasketColorChromeEmission Code5FinishChromeMaterialSteelProduct LineBudgetProduct TypePipe PlugsQuantity Per Pkg.8WarrantyLimited 90 Day WarrantyWeight0.2500Part Number6352G..

Contemporary Euro Style Shifter Boots are now available from Mr. Gasket Company. Made from a soft pliable, black rubber material, these boots feature multiple pleats for easy resistance free shifting. Universal in design, they can be used in conjunction with most consoles or factory trim plates. 6" nominal height. Euro Sport Angle style-4 1/2 " x 6" base.BrandMr. GasketEmission Code5Product TypeSh..

The 5-3/4" long stud fits air Filters up to 5" tall. The 1/4"-20 stud fits most carburetors. Dominator carburetors use the adapter since they have a 5/16"-18 tapped hole in the carburetor.Features:Zinc Plated Steel Stud, Adapter & Wing NutWill Fit Most Domestic Carburetors (Chrysler, Ford, and GM)Allows Use Of A 5.0" Inch Tall Air Filter ElementStud Can Be Cut to Fit Shorter Air Filters (where n..

This high quality filter is a must when your old filter becomes dirty and doesn't look fresh. This filter is white paper and brings out the bling in that engine compartment. Dirty filters will hurt performance and cause your engine to run poorly.Features:Fits Our 9790 Air CleanerMade Of High Paper MaterialHas A Rubber SealHas Wire Screen InsideHas Wire Mesh Outside To Prevent DamageBrandMr. Gasket..

These Mr. Gasket air filters are perfect for any project looking to gain unrestricted breathing power.BrandMr. GasketEmission Code5Filter Diameter12"Filter Height2.00 in.Filter TypeWhite PaperFinishWhiteProduct TypeAir FilterSize12"Weight0.5000Part Number6405G..

These Mr. Gasket air cleaner adapters end air cleaner fitment problems when you change carburetors. Molded from high-impact, heat-resistant material for durability.BrandMr. GasketEmission Code5Filter Height1"Filter TypeSpacerFinishBlackProduct TypeAir Cleaner AdapterSize5"Weight0.1300Part Number6406..

These Mr. Gasket air cleaner adapters end air cleaner fitment problems when you change carburetors. Molded from high-impact, heat-resistant material for durability.BrandMr. GasketEmission Code5Filter Height1"Filter TypeSpacerFinishBlackProduct TypeAir Cleaner AdapterSize5"Weight0.1500Part Number6407..

Mr. Gasket Air Cleaner Spacer and Adapter Kit eliminates air cleaner fit problems and includes spacers and adapters of different HEIghts that fit between the carburetor neck flange and the air filter assembly to allow the amount of clearance you need for your application. Kit includes (2) adapters for 5-1/8 in carb necks, (1) adapter for 3 in carb necks and (1) adapter for 2-5/8 in carb necks. 1/..

MSD now offers the perfect addition to your MSD Atomic EFI or other aftermarket electronic fuel injection, the 6EFI Ignition Control. The 6EFI is designed to work in harmony with electronic fuel injection systems and comes with detailed wiring instructions making installation a breeze. Increased throttle response, smoother idle, quicker starts and full ignition power throughout the entire RPM ran..

MSD is excited to announce the next generation of 6-Series ignition controls – the 6AL-2! The ignition control combines a new housing, new digital controls and more power in a sleek package. Inside the new cast aluminum housing you'll find an advanced micro-controller that manages the built-in two step rev-limiter. The spark output of the new box has been turned up to 535 volts of primary voltage ..