MSD

This hub allows you to expand the Power Grid system with up to four accessory modules.BrandMSDEmission Code5Product TypePower Grid ControllerPart Number77403..

Must be used with CAN-Bus Hub, PN 7740 to complete circuit. Without the CAN-Bus Terminator in place at the end of the CAN-Bus system, signals could be distorted. These distorted signals could result in permanent or intermittent problems that include but are not limited to; improper timing, false signals, and repetitious signals. Always be sure to have the MSD Controller and the CAN-Bus Terminator ..

Change the launch rpm limit (2-Step) on the fly, no need to login into software.Features:Make last minute changesChange Shift Light and RPM LaunchBrandMSDEmission Code4Part Number7751..

Now there is even more control with the PN 7761 module for the Power Grid System Controller. This module sets rpm limits based on slew rate (rpm acceleration) or based on time since launch. All of this is programmed seamlessly in MSD View. The ARC module stands for Advanced RPM Control, it basically allows your race car to remain consistent, pass after pass, controlling your engines rpm curve du..

This Power Grid module does exactly as its name sugests; retards the ignition timing in relation to boost, pressure. It also has an output wire that can be used to activate another device based on boost pressure, as well as an overboost shut-down feature that will shut the ignition off if boost exceeds the overboost target.BrandMSDEmission Code4Part Number7762..

MSD Boost Controllers are the most accurate and easy to use controllers on the market. Both controllers plug directly into the Power Grid via the CAN bus which allows user to make adjustments through MSD View software. MSD Boost controllers feature two boost curves that can be toggled on the fly, a user adjustable boost vs. timing retard curve, pressure switch and an over boost shutdown to protect..

The MSD Power Module is a fully programmable, four stage solid state relay that can handle up to 20 Amps of current per channel. The Power Module eliminates the need for electromechanical relays, fuses and timers. Outputs can be controlled independently or simultaneously, giving great flexibility. It can be configured as a digital output (i.e. ON/OFF) or as a Pulse Width Modulated output (i.e. PW..

The MSD Power Module is a fully programmable, four stage solid state relay that can handle up to 20 Amps of current per channel. The Power Module eliminates the need for electromechanical relays, fuses and timers. Outputs can be controlled independently or simultaneously, giving great flexibility. It can be configured as a digital output (i.e. ON/OFF) or as a Pulse Width Modulated output (i.e. PW..

Add valuable data logging capability to your Power Grid with the addition of the plug-n-play Wide Band O2 Module. Aside from providing O2 data to your Grid, the module also provides a 0-5v output to drive an air/fuel ratio gauge or provide a signal to other data loggers. Multiple modules and sensors can be connected to a single Power Grid setup if desired. The completely sealed unit uses a Bosc..

CAN-Bus Extension harness 2 Feet.BrandMSDEmission Code5Product TypePower GridPart Number7782..

CAN-Bus Extension harness 4 Feet.BrandMSDEmission Code5MakeUniversalProduct TypePower GridPart Number7784..

CAN-Bus Extension harness 6 Feet.BrandMSDEmission Code5MakeUniversalProduct TypePower GridPart Number7786..

The Harness, PN 7789, allows a user to use their existing Programmable-7 Harness to install the Power Grid System with minimal changes. The harness is designed to be a direct plug-in for all existing wires, but will need two new wires run if the user desires the two new inputs of the Power Grid.BrandMSDEmission Code5Part Number7789..

There has always been a niche group of hardcore racers and pullers that run nothing but the MSD 8 Ignition Series. If you liked it then, you're going to like it even better now! The MSD 8-Plus Ignition produces the same extreme output of the original 8-Series, yet is now in a smaller housing with improved efficiency and internal components. One distinct change is now a built-in 2-Step Rev Control..

Designed with Sprint cars in mind, the Pro-Mag 12LT is almost 30% lighter than the original Pro-Mag, but still produces the same incredible power. The compact housing sits an inch lower for improved clearance of the fuel injection, and it features a band clamp mount for easier timing adjustments. MSD has also designed a cap and rotor specifically for the 12LT series. The cap is injection molde..

Designed with Sprint cars in mind, the Pro-Mag 12LT is almost 30% lighter than the original Pro-Mag, but still produces the same incredible power. The compact housing sits an inch lower for improved clearance of the fuel injection, and it features a band clamp mount for easier timing adjustments. MSD has also designed a cap and rotor specifically for the 12LT series. The cap is injection molded f..

Designed with Sprint cars in mind, the Pro-Mag 12LT is almost 30% lighter than the original Pro-Mag, but still produces the same incredible power. The compact housing sits an inch lower for improved clearance of the fuel injection, and it features a band clamp mount for easier timing adjustments. MSD has also designed a cap and rotor specifically for the 12LT series. The cap is injection molded f..

Designed with Sprint cars in mind, the Pro-Mag 12LT is almost 30% lighter than the original Pro-Mag, but still produces the same incredible power. The compact housing sits an inch lower for improved clearance of the fuel injection, and it features a band clamp mount for easier timing adjustments. MSD has also designed a cap and rotor specifically for the 12LT series. The cap is injection molded f..

Designed with Sprint cars in mind, the Pro-Mag 12LT is almost 30% lighter than the original Pro-Mag, but still produces the same incredible power. The compact housing sits an inch lower for improved clearance of the fuel injection, and it features a band clamp mount for easier timing adjustments. MSD has also designed a cap and rotor specifically for the 12LT series. The cap is injection molded..

..